Just-better Deep Vacuum Pump Cartridge Manuel d'utilisateur télécharger pdf

Cartridge kit also contains 2

new O-rings, 1 cover gasket

and shaft seal. Before replacing

cartridge, be thoroughly familiar

with Replacing Pump

Cartridge procedures.

You will need the following tools:

Hammer

Medium Screwdriver

5/32" and/or 1/8" and 3/16"

Allen Wrench

11/16" Socket Head

3/8" or 7/16" Wrench or socket

Thread sealant

Vaseline or grease

DRAIN OIL

REMOVING MOTOR

1. Stand pump on oil cover. If

pumps has foot mounting

bracket, remove unit by loos-

ening foot screws.

(FIG. 1)

2. Turn coupling until setscrews

are facing you. With 5/32" or

1/8" Allen wrench (depending

on model) loosen setscrew on

motor shaft. (FIG. 2) Loosen

four (4) motor thru bolts (FIG.

3). Remove motor. DO NOT

REMOVE BOLTS FROM MO-

TOR AT ANY TIME.

If old cartridge is frozen, i.e.

coupler will not turn, remove

oil cover (FIG. 4) and four (4)

cartridge bolts (FIG. 5). By

turning cartridge, coupler will

rotate into position.

3. Loosen setscrews on coupler

and remove coupling.

(FIG. 2)

Form #10086-308/1M

Printed in U.S.A.

JB INDUSTRIES

Aurora, IL 60507 U.S.A.

Part # Replacement For

D10043 DV-42 obsolete

D10086 DV-3 & DV-85C obsolete

D10087 DV-85 obsolete

D10128 DV-5 & DV-127 obsolete

D10143 DV-142 (4 Digit Serial No.) obsolete

PR-202 DV-85N

PR-203 DV-142N

PR-204 DV-200N

PR-212 DV-42N

PR-214 DV-285N

PR-302 DV-85N (Manufactured after January, 2000)

PR-303 DV-142N (Manufactured after January, 2000)

PR-304 DV-200N (Manufactured after January, 2000)

PR-305 DV-42N (Manufactured after January, 2000)

PR-314 DV-285N (Manufactured after January, 2000)

NOTE: Instructions pertain to

all pump series. Pump

styles may vary from il-

lustrations.

REPLACING MOTOR

1. With pump standing on oil

cover, rotate coupling so set

screws are facing trap assem-

bly opening. Re-install motor

while aligning at side of motor

shaft with set screw.

IMPORTANT

ASSEMBLE IN THIS ORDER

a. Tighten four (4) motor screws

and then

b. Tightened coupler set screw

on motor shaft.

2. Re-install foot mounting bracket

and rubber feet.

Should you need further assistance call our toll

free Technical Service number 1-800-323-0811.

Visit our web site at: www.jbind.com

E-mail: [email protected]

Loosen 4 Motor Bolts. Lift Motor Off.

(Do Not Remove Bolts)

Trap

Loosen Coupler

Setscrew

On Motor Shaft

FIG. 1

(Models

with Foot

Mounting

Bracket

only)

FIG. 2

FIG. 3

Replacement Instructions

for Deep Vacuum Pump Cartridge

BEFORE OPERATING

1. Be sure pump switch is in “Off”

position and plug in.

2. Open oil drain and intake cap.

While pump is running, im-

mediately place 2 or 3 ounces

of fresh oil into intake and run

pump for 3 or 4 seconds. Re-

peat procedure at least 2 times.

Allow oil to drain out.

3. Close oil drain and replace

intake cap.

4. Fill with fresh FastVac Deep

Vacuum Pump oil to top edge of

oil level line. For those pumps

without line, the correct level is

1/8" below top of sight glass.

Replace oil ll plug.

5. Run Vacuum Test.

Trap

Loosen Coupler

Setscrew

On Motor Shaft

1 2

Replacement Instructions 1
1/8" 2

Résumé du contenu

Page 1 - Replacement Instructions

Cartridge kit also contains 2 new O-rings, 1 cover gasket and shaft seal. Before replacing cartridge, be thoroughly familiar with Replacing Pump Cart

Page 2 - 1/8"

FIG. 4FIG. 5FIG. 6FIG. 7REMOVING OIL COVER 1. Using 3/16" Allen wrench remove 6 socket head cap screws from oil cover. (FIG. 4)REMOVING CARTRIDGE

Commentaires sur ces manuels

Pas de commentaire

Just-better Deep Vacuum Pump Cartridge Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pompes Just-better Deep Vacuum Pump Cartridge. Just Better Deep Vacuum Pump Cartridge User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes Just-better Deep Vacuum Pump Cartridge